
To crossfade between two tracks, load both files into the free Audio Joiner, set the Crossfade between tracks slider to the overlap you want, and click Join & Download Audio. The outgoing song fades out while the incoming one fades in over the same stretch of time, and you get back one file. The slider is the easy part. This guide covers the decisions that make a crossfade sound deliberate rather than muddy: how long it should be, what shape the fade takes, and what to fix in tempo and key before the two tracks ever meet.
If you want the full workflow for a long multi-song set, see How to Make a Continuous DJ Mix. This page is about the transition itself.
A crossfade overlaps the end of one track with the start of the next. During the overlap the first track's volume falls toward silence while the second rises from silence, so for a few seconds you hear both. Compare that with a plain fade, which takes one clip to or from silence on its own (How to Fade Audio In and Out (Free) covers that).
Because the tracks overlap, the joined file is shorter than the two originals added together. Two 3-minute songs joined with a 6-second crossfade come out at 5:54, not 6:00. The Audio Joiner shows this in its Merged file estimation line, which updates as you move the slider.
joined_ followed by a timestamp.That's all the joiner needs. The rest of this article is about getting a good result out of step 3.
One length for every junction. If you join five files, every transition gets the same crossfade. When you need different lengths, join in passes: crossfade tracks A and B at 8 seconds, download, then load that file with track C and join at 1 second.
Very short clips get shorter fades. Each overlap is capped at half the length of either file at that junction. A 4-second sound effect can take at most a 2-second crossfade, whatever the slider says. Otherwise a short clip's fade-in would run straight into its own fade-out.
Loud overlaps are turned down, never up. Two loud tracks playing at once can add up past full scale (0 dBFS, the loudest level a digital file can hold) and clip. When a crossfade is on and that would happen, the joiner lowers the whole joined file just enough to stay below clipping. It never raises the level. If one song is much quieter than the other, level them first with the Volume Normalizer, because the joiner won't balance them for you.
The shape of the fade matters as much as its length. There are two common shapes.
A linear crossfade moves each track's volume in a straight line: the outgoing track goes from 100% to 0% while the incoming goes from 0% to 100%. At the midpoint both sit at 50%. That sounds balanced, but for two different songs it isn't. Unrelated audio adds by power, not by amplitude, and two signals at half amplitude add up to roughly 3 dB quieter than either track alone. You hear a small dip in loudness right in the middle of the transition.
An equal-power crossfade uses curves (a sine rising, a cosine falling) so the combined power stays constant. At the midpoint each track sits at about 71% amplitude, roughly 3 dB down, and the two together land at roughly the same loudness as either song on its own. No dip, no bump.
The Audio Joiner uses equal-power for every crossfade. For the usual job, joining two different songs, two speech segments or two takes of different material, that's the right call.
There is one case where linear wins. When the two sides are nearly identical, such as two copies of the same loop or two edits of the same take, the signals add by amplitude instead. Equal-power then produces a bump of about 3 dB in the middle, and linear stays flat. The joiner has no linear option, so for a seamless loop of identical material keep the crossfade very short, or look at Audio Looper: How to Loop Audio Seamlessly for that specific job.
There's no correct number, only a sensible starting point for what you're joining. Use these as first guesses, listen, and adjust.
| What you're joining | Starting point | Why |
|---|---|---|
| Podcast or speech segments | 0.5 to 1 s | Long enough to hide a click or a change in room tone, short enough that two voices don't talk over each other. |
| Songs in a playlist or album | 2 to 4 s | Smooths the gap without blending two different songs for long. |
| Beat-matched, DJ-style transitions | 4 to 8 s | Gives the incoming groove time to establish. Best when tempo and key are matched (see below). |
| Ambient, drone or sleep audio | 8 to 12 s | Slow material has no beat to clash, so a long blend just sounds like a gradual change of scene. |
For beat-based music, think in bars rather than seconds. In 4/4 time a bar lasts 240 divided by the BPM: at 120 BPM that's 2 seconds, so 4 bars is 8 seconds. At 128 BPM a bar is 1.875 seconds, so 4 bars is 7.5 seconds, which the slider can hit exactly. A crossfade that spans a whole number of bars tends to sound intentional.
A crossfade is the one moment where two songs play at once, so any mismatch between them is exposed rather than hidden. Two checks prevent most bad transitions.
If the two tracks run at different speeds, their beats drift apart during the overlap and you get a stumbling, flamming rhythm. Find each track's tempo with the BPM Finder (How to Find the BPM of Any Song (3 Ways) walks through it). If they're a few BPM apart, nudge one with the Speed Changer, which changes tempo while keeping the pitch. Beatmatching and Key Matching Explained covers how close is close enough.
Matching tempo isn't quite enough on its own, because the joiner has no beat-grid alignment. It starts the second track exactly one crossfade length before the first one ends. So the beats only line up if both edges are clean. Trim the outgoing track in the Audio Cutter so it ends right on a bar line, trim the incoming one so it starts right on a downbeat, then set a crossfade that's a whole number of bars at that shared tempo. Trimming also removes long silent outros and slow intros, which would otherwise eat the overlap with dead air.
Two songs in clashing keys sound sour while they overlap, even when the beats agree. Check both with the Key Finder. Same key, or closely related keys such as a relative major and minor, blend well. That idea is the basis of What Is Harmonic Mixing? A Key Finder Guide. If two songs you want together clash, shift one with the Pitch Changer by a semitone or two, or keep the crossfade short so the clash passes quickly.
Speech and ambient material rarely needs either check. Song-to-song transitions almost always benefit from both.
The crossfade sounds shorter than I set. One of the files at that junction is short. The overlap is capped at half of the shorter file, so a 5-second clip can only take 2.5 seconds.
The transition dips or swells in volume. A swell usually means the two sides are near-identical material, where equal-power adds a little level. A dip usually means one track is fading out on its own (a recorded fade-out) on top of the crossfade. Trim the built-in fade off first.
The whole file came out quieter than the originals. That's the clipping protection. The overlap would have peaked above full scale, so the joined file was turned down. Normalize the finished file if you need it louder.
A stereo song came out in mono. The joiner brings everything to the first file's sample rate and channel count. A mono file in a stereo join is copied to both sides, but if the first file is mono the whole result is mono. Put a stereo track first in the list.
If you don't need an overlap at all, How to Combine Songs Into One File covers the simpler end-to-end join. For more step-by-step workflows, browse the Audio How-To Guides.
What is the best crossfade length between two songs?
For songs in a playlist, 2 to 4 seconds is a good starting point. Beat-matched dance tracks often sound best at 4 to 8 seconds, ideally a whole number of bars, while speech works at 0.5 to 1 second and ambient material can stretch to 8 to 12 seconds. Treat these as first guesses: listen to the transition and adjust until neither track feels rushed or muddy.
Is equal-power or linear crossfade better?
Equal-power is better for joining two different pieces of audio, because it keeps perceived loudness steady through the transition, while a linear crossfade dips by about 3 dB in the middle. Linear is better when both sides are nearly identical, such as two copies of the same loop, where equal-power causes a small bump. Vocal Cut's Audio Joiner uses equal-power for every crossfade.
Why is my joined file shorter than the two tracks added together?
A crossfade overlaps the end of one track with the start of the next, so that shared stretch is only counted once. Joining two 3-minute tracks with a 6-second crossfade gives a 5:54 file. With the crossfade set to Off, the files are joined end to end instead, and the result is exactly as long as the tracks combined.
Can I crossfade MP3 files without converting them first?
Yes. The Audio Joiner reads MP3, WAV, M4A, FLAC and other common formats directly in the browser, matches them all to the first file's sample rate and channel count, and exports the crossfaded result as WAV, MP3 or Opus. Opus is not offered on Safari. Your audio never leaves your device during any of this.
Do the two tracks need the same tempo and key to crossfade?
Not always, but it helps for music. During the overlap both songs play at once, so different tempos make the beats drift and clashing keys sound sour. Check them with a BPM finder and key finder, then adjust with a speed changer or pitch changer if needed. Speech and ambient audio rarely need either check.